 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SIDACtor (R) Protection Thyristors High Surge Current Protection SIDACtor(R) Primary Protection Balanced Series Description - Modified TO-220 The SIDACtor(R) Primary Protection Balanced Series Modified TO-220 are thyristor devices designed for use in primary protection applications. The series provides a single port overvoltage solution that enables applications to comply with the balance requirements of GR-974 and GTS-8700. Please contact Littelfuse to discuss your particular application and regulatory requirements. Features and Benefits Agency Approvals Agency Agency File Number E133083 High holding current options available Balanced overvoltage protection Failsafe option available Low voltage overshoot Low on-state voltage Does not degrade with use Fails short circuit when surged in excess of ratings Single-port protection Modified TO-220 Package Lead forms available Pinout Designation Applicable Global Standards GR-974 PIN 1 PIN 2 PIN 3 UL 497 ITU K.28 GTS-8700 Schematic Symbol 1 (T) 3 (R) 2 (G) Electrical Characteristics VS VDRM @lDRM=5A @100V/s V min V max Pins 1-2, 3-2, 1-3 130 180 150 210 170 250 200 270 230 300 270 350 300 400 420 600 IH* mA min 150 150 150 150 150 150 150 150 IS mA max 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT@IT= 2.2 Amps V max 8 8 8 8 8 8 8 8 Capacitance Pin 1-2 / 3-2 Tip-Ground, Ring-Ground pF min 65 55 55 50 50 45 45 40 pF max 95 85 85 75 75 70 65 60 Pin 1-3 Tip-Ring pF min 40 35 30 30 30 25 25 20 pF max 60 55 55 50 50 45 45 40 Part Number Marking P1553ACLxx P1803ACLXX P2103ACLxx P2353ACLxx P2703ACLxx P3203ACLxx P3403ACLxx P5103ACLxx P1553AC P1803AC P2103AC P2353AC P2703AC P3203AC P3403AC P5103AC Notes: * Higher holding current available by special order. Contact Littelfuse for additional information. - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 199 - Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. - xx Part Number Suffix: `RP' (Reel pack), Blank (Bulk pack), `60' (Type 60 lead form bulk pack), `FS1' (Failsafe option bulk pack). Refer to Part Numbering section for additional details. Revised: February 22, 2011 SIDACtor (R) Protection Thyristors High Surge Current Protection Surge Ratings IPP Series 0.2x310 1 0.5x700 2 A min C Notes: 1 Current waveform in s 2 Voltage waveform in s - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40C < TJ < 2x10 1 2x10 2 A min 500 8x20 1 1.2x50 2 A min 400 10x160 1 10x160 2 A min 200 10x560 1 10x560 2 A min 150 5x320 1 9x720 2 A min 200 10x360 1 10x360 2 A min 175 10x1000 1 10x1000 2 A min 100 5x310 1 10x700 2 A min 200 ITSM 50/60 Hz A min 50 di/dt A/s max 500 50 Thermal Considerations Package Modified TO-220 Symbol TJ TS PIN 1 PIN 2 PIN 3 Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit C C R0JA 50 C/W V-I Characteristics +I tr x td Pulse Waveform IPP - Peak Pulse Current - %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t - Time (s) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change - % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25C) 14 12 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 C 25C Junction Temperature (TJ) - C Ratio of Case Temperature (TC) - C (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 200 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors High Surge Current Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3C/sec. Max. 3C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5C of actual Peak Temp (tp) Ramp-down Rate Time 25C to Peak Temp (TP) Do not exceed 30 secs. Max. 6C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25C to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Part Numbering Autoclave (Pressure Cooker Test) Resistance to Solder Heat P xxx 3 A C L xx TYPE P = SIDACtor PACKING OPTIONS Blank: Bulk RP: Reel Pack 60: Type 60 Lead Form (for type 60 orders, contact factory). Moisture Sensitivity Level MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE RoHS COMPLIANT IPP RATING Part Marking XXXXXXXXX Part Marking Code (Refer to Electrical Characteristics Table) P xxx 3 A C L FS1 TYPE P = SIDACtor FAILSAFE OPTION* RoHS COMPLIANT IPP RATING * Failsafe devices are only offered in bulk pack, reel pack not available. xxxxx Date Code MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 201 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors High Surge Current Protection Dimensions - Modified TO-220 A O Dimensions - Modified TO-220 with Failsafe Inches Min Max 0.410 0.375 0.130 0.575 0.035 0.205 0.105 0.075 0.085 0.024 0.188 0.310 Millimeters Min 9.14 2.80 0.63 4.95 2.41 1.52 1.78 0.46 4.52 7 .37 Max 9.53 3.30 0.89 5.21 2.67 1.90 2.16 0.61 4.78 7 .87 D A F Temperature Measurement Point P PIN 3 PIN 2 PIN 1 L K H J M N 0.400 0.360 0.110 0.540 0.025 0.195 0.095 0.060 0.070 0.018 0.178 0.290 10.16 10.42 D F G H J K L M G 13.71 14.61 The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. N O P Tape and Reel Specification - Modified TO-220 0.240 (6.10) 1.626 (41.15) 0.720 (18.29) 0.360 (9.14) 0.500 (12.7) Dimensions - Modified TO-220 Type 60 with Failsafe 0.019 (0.5) 0.750 0.010 (19.05 0.25) 0.100 (2.54) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed 1.968 (50.0) Packing Options Package Type Description Modified TO-220 Tape and Reel Pack A Modified TO-220 Bulk Pack Modified TO-220 Type 60 Lead Form Bulk Pack Quantity 700 500 Added Suffix RP (no added suffix) 60 (special order item, contact factory for details) Industry Standard EIA-468-B N/A 500 N/A (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 202 Revised: February 22, 2011 |
Price & Availability of P1803ACLXX
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |